Hotpoint Washer WMUD User Manual

Instructions for use  
WASHING MACHINE  
Contents  
GB  
Installation, 2-3-4-5  
Unpacking and levelling  
Connecting the electricity and water supplies  
The first wash cycle  
GB  
English,1  
Technical data  
Care and maintenance, 6  
Cutting off the water or electricity supply  
Cleaning the washing machine  
Cleaning the detergent dispenser drawer  
Caring for the door and drum of your appliance  
Cleaning the pump  
Checking the water inlet hose  
Precautions and tips, 7  
General safety  
Disposal  
Opening the porthole door manually  
WMUD 9627  
Description of the washing machine, 8-9  
Control panel  
Display  
Running a wash cycle, 10  
Wash cycles and functions, 11  
Table of wash cycles  
Wash functions  
Detergents and laundry, 12  
Detergent dispenser drawer  
Preparing the laundry  
Special wash cycles  
Load balancing system  
Troubleshooting, 13-14  
Assistance, 15-16  
1
 
Connecting the drain hose  
Connect the drain  
• the supply voltage is included within the  
values indicated on the Technical Data Plate  
fixed on the machine.  
GB  
hose, without ben-  
ding it, to a draining  
duct or a wall drain  
situated between 65  
and 100 cm from the  
floor;  
• the socket is compatible with the washing  
machines plug. If this is not the case, repla-  
ce the socket or the plug.  
65 - 100 cm  
Your appliance is now supplied with a 13 amp  
fused plug it can be plugged into a 13 amp  
socket for immediate use. Before using the  
appliance please read the instructions below.  
WARNING - THIS APPLIANCE MUST BE  
EARTHED.  
The drain hose may  
be connected to  
an under-sink trap.  
Before connecting  
the drain hose from  
the machine ensure  
that any blanks or  
removable ends have  
been taken off the  
spigot.  
THE FOLLOWING OPERATIONS SHOULD  
BE CARRIED OUT BY A QUALIFIED ELECTRI-  
CIAN.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be  
used, and the fuse cover re-fitted. If the fuse  
cover is lost, the plug must not be used until a  
replacement is obtained.  
Where it connects to  
the waste water pipe  
cut end off spigot or  
remove the blanking cap  
Replacement fuse covers:  
If a replacement fuse cover is fitted, it must be  
of the correct colour as indicated by the colou-  
red marking or the colour that is embossed in  
words on the base of the plug. Replacements  
can be obtained directly from your nearest  
Service Depot.  
If it is placed over  
the edge of a basin  
or sink be sure the  
free end of the hose  
should not be under-  
water.  
Removing the plug:  
If your appliance has a non-rewireable moul-  
ded plug and you should wish to re-route the  
mains cable through partitions, units etc.,  
please ensure that either:  
the plug is replaced by a fused 13 ampere  
rewireable plug bearing the BSI mark of ap-  
proval.  
! We advise against the use of hose extensions;  
in case of absolute need, the extension must  
have the same diameter as the original hose  
and must not exceed 150 cm in length.  
Ensure that if the drain hose is pushed into  
a standpipe, that the end does not go down  
more than 15cms (6 inches). If the hose is pu-  
shed down too far, this may cause the machine  
to self -syphon ie. continuously empty as it is  
filling.  
or:  
the mains cable is wired directly into a 13  
amp cable outlet, controlled by a switch, (in  
compliance with BS 5733) which is accessible  
without moving the appliance.  
Disposing of the plug:  
Ensure that before disposing of the plug itself,  
you make the pins unusable so that it cannot  
be accidentally inserted into a socket.  
Electric connection  
Instructions for connecting cable to an alternati-  
Before plugging the appliance into the mains  
socket, make sure that:  
ve plug:  
Important: the wires in the mains lead are co-  
loured in accordance with the following code:  
Green & Yellow Earth  
the socket is earthed and in compliance with  
the applicable law;  
Blue  
Brown  
Neutral  
Live  
the socket is able to sustain the appliances  
maximum power load indicated on the Tech-  
nical Data Plate fixed on the machine;  
3
 
As the colours of the wires in the lead may not  
correspond with the coloured markings iden-  
tifying the terminals in your plug, proceed as  
follows:  
! The power supply cable must only be repla-  
GB  
ced by an authorised serviceman.  
Warning! The company denies all liability if and  
when these norms are not respected.  
Connect Green & Yellow wire to terminal  
marked E or or coloured Green or Green &  
Yellow.  
The first wash cycle  
Connect Brown wire to terminal marked L or  
coloured Red.  
Once the appliance has been installed, and  
before you use it for the first time, run a wash  
cycle with detergent and no laundry, using the  
programme “Auto Clean” (see “Cleaning the  
washing machine”).  
Connect Blue wire to terminal marked N or  
coloured Black.  
If a 13 amp plug (BS 1363) is used it must be  
fitted with a  
13 amp fuse, either in the plug or adaptor or  
at the distribution board.  
If you are in any doubt regarding the electrical  
supply to your machine, consult a qualified  
electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
BLUE  
NEUTRAL (N)  
LIVE (L)  
EARTH (E)  
BROWN  
GREEN & YELLOW  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
CROSS-BAR  
CORD GRIP  
BLUE  
Disposing of the appliance:  
When disposing of the appliance please re-  
move the plug by cutting the mains cable as  
close as possible to the plug body and dispo-  
se of it as described on the previous page.  
! The washing machine should not be installed  
in an outdoor environment, not even where  
the area is sheltered, because it may be very  
dangerous to leave it exposed to damp, rain  
and thunderstorms.  
! When the washing machine is installed, the  
mains socket must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent  
or dangerously compressed.  
4
 
GB  
Technical data  
Model  
WMUD 9627  
width 59.5 cm  
Dimensions height 85 cm  
depth 60.5 cm  
Capacity  
from 1 to 9 kg  
please refer to the technical  
data plate fixed to the ma-  
chine  
Electrical  
connections  
maximum pressure  
1 MPa (10 bar)  
minimum pressure  
0.05 MPa (0.5 bar)  
drum capacity 62 litres  
Water con-  
nections  
up to 1600 rotations per  
minute  
Spin speed  
Test wash  
cycles in  
accordan-  
ce with  
programme  
(60°)  
(1st press of the button);  
Standard Cotton 60°.  
directives  
1061/2010  
and  
programme  
(2nd press of the button);  
Standard Cotton 40°.  
(40°)  
1015/2010  
This appliance conforms to  
the following EC Directives:  
- 2004/108/EC (Electromagne-  
tic Compatibility)  
- 2006/95/EC (Low Voltage)  
- 2002/96/EC  
5
 
Care and maintenance  
Cutting off the water and electri-  
city supplies  
Caring for the door and drum of  
GB  
your appliance  
• Turn off the water tap after every wash cycle.  
This will limit wear on the hydraulic system in-  
side the washing machine and help to prevent  
leaks.  
• Always leave the porthole door ajar in order  
to prevent unpleasant odours from forming.  
Cleaning the pump  
• Unplug the washing machine when cleaning  
it and during all maintenance work.  
The washing machine is fitted with a self-clea-  
ning pump which does not require any mainte-  
nance. Sometimes, small items (such as coins  
or buttons) may fall into the pre-chamber which  
protects the pump, situated in its bottom part.  
Cleaning the washing machine  
• The outer parts and rubber components  
of the appliance can be cleaned using a soft  
cloth soaked in lukewarm soapy water. Do not  
use solvents or abrasives.  
! Make sure the wash cycle has finished and  
unplug the appliance.  
• The washing machine has a “Auto Clean”  
programme for its internal parts that must be  
run with no load in the drum.  
To access the pre-chamber:  
1. using a screwdri-  
ver, remove the cover  
panel on the lower  
front part of the wa-  
shing machine (see  
figure);  
To help the wash cycle  
A
B
you may want to use  
either the detergent  
(i.e. a quantity 10% the  
quantity specified for  
lightly-soiled garments)  
or special additives to  
clean the washing ma-  
chine. We recommend  
running a cleaning  
2. unscrew the lid  
by rotating it anti-  
clockwise (see figu-  
re): a little water may  
trickle out. This is  
perfectly normal;  
programme every 40 wash cycles.  
To start the programme press buttons A and  
B simultaneously for 5 seconds (see figure).  
The programme will start automatically and will  
run for about 70 minutes. To stop the cycle  
press the START/PAUSE button.  
Cleaning the detergent dispenser  
drawer  
Remove the dispenser  
3. clean the inside thoroughly;  
4. screw the lid back on;  
1
by raising it and pul-  
ling it out (see figure).  
Wash it under running  
water; this operation  
should be repeated  
frequently.  
5. reposition the panel, making sure the hooks  
are securely in place before you push it onto  
the appliance.  
Checking the water inlet hose  
2
Check the inlet hose at least once a year. If  
there are any cracks, it should be replaced  
immediately: during the wash cycles, water  
pressure is very strong and a cracked hose  
could easily split open.  
! Never use second-hand hoses.  
6
 
Precautions and tips  
! This washing machine was designed and constructed in  
accordance with international safety regulations. The fol-  
lowing information is provided for safety reasons and must  
therefore be read carefully.  
Opening the porthole door manually  
GB  
In the event that it is not possible to open the porthole  
door due to a powercut, and if you wish to remove the  
laundry, proceed as follows:  
General safety  
1. remove the plug from the  
electrical socket.  
• This appliance was designed for domestic use only.  
2. make sure the water level  
inside the machine is lower  
than the door opening; if it  
is not, remove excess water  
using the drain hose, collec-  
ting it in a bucket as indicated  
in the figure.  
• This appliance is not intended for use by persons (inclu-  
ding children) with reduced physical, sensory or mental  
capabilities, or lack of experience and knowledge, unless  
they have been given supervision or instruction concer-  
ning use of the appliance by a person responsible for  
their safety. Children should be supervised to ensure that  
they do not play with the appliance.  
• Do not touch the machine when barefoot or with wet or  
damp hands or feet.  
3. using a screwdriver, remo-  
ve the cover panel on the lo-  
wer front part of the washing  
machine (see figure).  
• Do not pull on the power supply cable when unplugging  
the appliance from the electricity socket. Hold the plug  
and pull.  
• Do not open the detergent dispenser drawer while the  
machine is in operation.  
• Do not touch the drained water as it may reach extreme-  
ly high temperatures.  
• Never force the porthole door. This could damage the safety  
lock mechanism designed to prevent accidental opening.  
• If the appliance breaks down, do not under any circum-  
stances access the internal mechanisms in an attempt  
to repair it yourself.  
• Always keep children well away from the appliance while  
it is operating.  
• The door can become quite hot during the wash cycle.  
• If the appliance has to be moved, work in a group of two  
or three people and handle it with the utmost care. Never  
try to do this alone, because the appliance is very heavy.  
• Before loading laundry into the washing machine, make  
sure the drum is empty.  
4. pull outwards using the tab as indicated in the figure,  
until the plastic tie-rod is freed from its stop position; pull  
downwards and open the door at the same time.  
Disposal  
5. reposition the panel, making sure the hooks are securely  
in place before you push it onto the appliance.  
Disposing of the packaging materials: observe local regu-  
lations so that the packaging may be re-used.  
The European Directive 2002/96/EC on Waste Electrical  
and Electronic Equipment, requires that old household  
electrical appliances must not be disposed of in the normal  
unsorted municipal waste stream. Old appliances must be  
collected separately in order to optimise the recovery and  
recycling of the materials they contain and reduce the im-  
pact on human health and the environment. The crossed  
out “wheeled bin” symbol on the product reminds you of  
your obligation, that when you dispose of the appliance it  
must be separately collected. Consumers should contact  
their local authority or retailer for information concerning the  
correct disposal of their old appliance.  
7
 
Description of the washing machine  
Control panel  
CLEANING  
ACTION  
button  
SPIN SPEED  
GB  
ON/OFF  
button  
button  
DISPLAY  
START/PAUSE  
button with  
indicator light  
MY  
CYCLE  
button  
WASH  
CYCLE  
SELECTOR  
buttons  
FUNCTION  
Detergent dispenser drawer  
buttons  
DELAY  
TIMER  
button  
TEMPERATURE  
button  
ANTI  
ALLERGY  
RINSE  
button  
CHILD LOCK  
button  
Detergent dispenser drawer: used to dispense deter-  
gents and washing additives (see “Detergents and laundry”).  
TEMPERATURE button : press to decrease the tem-  
perature: the value will be shown on the display.  
ON/OFF button : press this briefly to switch the ma-  
chine on or off. The START/PAUSE indicator light, which  
flashes slowly in a green colour shows that the machine is  
switched on. To switch off the washing machine during the  
wash cycle, press and hold the button for approximately 3  
seconds; if the button is pressed briefly or accidentally the  
machine will not switch off. If the machine is switched off  
during a wash cycle, this wash cycle will be cancelled.  
CHILD LOCK button: to activate the control panel lock,  
press and hold the button for approximately 2 seconds.  
When the symbol  
is illuminated, the control panel is  
locked (apart from the ON/OFF button). This means it  
is possible to prevent wash cycles from being modified  
accidentally, especially where there are children in the  
home. To deactivate the control panel lock, press and hold  
the button for approximately 2 seconds.  
WASH CYCLE SELECTOR buttons: used to set the  
desired wash cycle (see “Table of wash cycles”).  
DELAY TIMER button: press to set a delayed start time  
for the selected wash cycle. The delay time will be shown  
on the display.  
MY CYCLE button: press and hold the button to store a  
cycle with your own set of preferences in the memory of  
the machine. To recall a previously stored cycle, press the  
MY CYCLE button.  
START/PAUSE button with indicator light: when the gre-  
en indicator light flashes slowly, press the button to start a  
wash cycle. Once the cycle has started the indicator light  
will remain lit in a fixed manner. To pause the wash cycle,  
press the button again; the indicator light will flash in an  
FUNCTION buttons: press the button to select the  
desired function. The corresponding indicator light on the  
display will switch on.  
orange colour. If the symbol  
is not illuminated, the door  
may be opened. To start the wash cycle from the point at  
which it was interrupted, press the button again.  
CLEANING ACTION button: to select the desired wash  
intensity.  
Standby mode  
This washing machine, in compliance with new energy sa-  
ving regulations, is fitted with an automatic standby system  
which is enabled after about 30 minutes if no activity is  
detected. Press the ON-OFF button briefly and wait for the  
machine to start up again.  
ANTI ALLERGY RINSE button: press to select the  
desired rinse type.  
SPIN button : press to reduce or completely exclude  
the spin cycle - the value is indicated on the display.  
Consumption in off-mode: 0,5 W  
Consumption in Left-on: 0,5 W  
8
 
Display  
GB  
A
X
B
Z
D
E
C
Y
F
The display is useful when programming the machine and provides a great deal of information.  
The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa-  
tion relating to the progress status of the wash cycle.  
String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the  
time remaining until the start of the selected wash cycle.  
String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does not include  
a spin cycle, the string remains unused.  
String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if the tempe-  
rature of the wash cycle cannot be modified, the string remains unused.  
Indicator lights F correspond to the functions and light up when the selected function is compatible with the set wash cycle.  
Door locked symbol  
If the symbol is lit, this indicates that the washing machine door is locked to prevent it from being opened accidentally. To  
prevent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.  
N.B.: if the DELAY TIMER function has been activated, the door cannot be opened; pause the machine by pressing the  
START/PAUSE button if you wish to open it.  
9
 
Running a wash cycle  
1. SWITCH THE MACHINE ON. Press the On/Off  
button ; the text POWER ON will appear on the  
display and the START/PAUSE indicator light will flash  
slowly in a green colour.  
drum rotation to ensure washing results are perfect for  
GB  
delicate garments.  
Set the rinse type.  
Option “Anti Allergy Rinse” makes it possible to select  
the desired rinse type for sensitive skin. Press the button  
once for the “Extra Rinse” level, which makes it possible  
to select an additional rinse after the standard cycle rinse  
and remove all traces of detergent. Press the button  
again for the “Sensitive Skin” level, which makes it  
possible to select two additional rinses to the standard  
cycle rinses; it is recommended for very sensitive skin.  
Press the button for the third time for the “Anti allergy  
Rinse” level, which makes it possible to select three  
additional rinses to the standard cycle rinses and remove  
major allergens such as pollen, mites, cat and dog hair.  
Press the button again to go back to the “Normal Rinse”  
rinse type. If the current adjustment can be neither set  
2. LOAD THE LAUNDRY. Open the porthole door.  
Load the laundry, making sure you do not exceed  
the maximum load value indicated in the table of  
programmes on the following page.  
3. MEASURE OUT THE DETERGENT. Open the  
detergent dispenser drawer and pour the detergent into  
the relevant compartments as described in “Detergents  
and laundry”.  
4. CLOSE THE DOOR.  
5. SELECT THE WASH CYCLE. Press one of the WASH  
CYCLE SELECTOR buttons to select the required wash  
cycle; the name of the wash cycle will appear on the  
display. A temperature and spin speed is set for each  
wash cycle; these may be adjusted. The duration of the  
cycle will appear on the display.  
nor changed, the display will show “Not allowed”.  
Modifying the cycle settings.  
• Press the button to enable the function; the indicator  
light corresponding to the button will switch on.  
• Press the button again to disable the function; the  
indicator light will switch off.  
! If the selected function is not compatible with the  
programmed wash cycle, the indicator light will flash  
and the function will not be activated.  
! If the selected function is not compatible with  
another function which has been selected previously,  
the indicator light corresponding to the first function  
selected will flash and only the second function will  
be activated; the indicator light corresponding to the  
enabled function will remain lit.  
6. CUSTOMISE THE WASH CYCLE. Use the relevant  
buttons:  
Modifying the temperature and/or spin  
speed. The machine automatically selects the  
maximum temperature and spin speed set for the  
selected wash cycle; these values cannot therefore  
be increased. The temperature can be decreased by  
pressing the  
setting is reached. The spin speed may be progressively  
reduced by pressing the button, until it is completely  
button, until the cold wash “OFF”  
excluded (the “OFF” setting). If these buttons are  
pressed again, the maximum values are restored.  
! Exception: if the  
(60°) (1st press of the button)  
programme is selected, the temperature can be  
increased up to a value of 90°C.  
! The functions may affect the recommended load value  
and/or the duration of the cycle.  
7. START THE PROGRAMME. Press the START/  
PAUSE button. The corresponding indicator light will  
become green, remaining lit in a fixed manner, and the  
door will be locked (the DOOR LOCKED symbol will be  
on). During the wash cycle, the name of the phase in  
progress will appear on the display. To change a wash  
cycle while it is in progress, pause the washing machine  
using the START/PAUSE button (the START/PAUSE  
indicator light will flash slowly in an orange colour);  
then select the desired cycle and press the START/  
PAUSE button again. To open the door while a cycle  
is in progress, press the START/PAUSE button; if the  
Setting a delayed start.  
To set a delayed start for the selected programme,  
press the corresponding button repeatedly until the  
required delay period has been reached. When this  
option is enabled, the  
symbol lights up on the  
display. To remove the delayed start function press the  
button until the text “OFF” appears on the display.  
Set the desired wash intensity.  
Option “Cleaning Action” makes it possible to optimise  
washing based on the level of soil in the fabrics and on  
desired wash cycle intensity.  
Select the wash programme: the cycle will be  
automatically set to “Normal” as optimised for garments  
with an average level of soil (this setting is not applicable  
to the “Wool” cycle, which is automatically set to  
Delicate”).  
For heavily-soiled garments press button “Cleaning  
Action” until the “Super Wash” level is reached. This  
level ensures a high-performance wash due to a larger  
quantity of water used in the initial phase of the cycle  
and due to increased drum rotation. It is useful when  
removing the most stubborn stains.  
DOOR LOCKED  
symbol is switched off the door  
may be opened. Press the START/PAUSE button again  
to restart the wash cycle from the point at which it was  
interrupted.  
8. THE END OF THE WASH CYCLE. This will be  
indicated by the text “END OF CYCLE” on the display;  
when the DOOR LOCKED  
symbol switches off  
the door may be opened. Open the door, unload the  
laundry and switch off the machine.  
! If you wish to cancel a cycle which has already begun,  
For lightly-soiled garments or a more delicate treatment  
of the fabrics, press button “Cleaning Action” until the  
Delicate” level is reached. The cycle will reduce the  
press and hold the  
button. The cycle will be stopped  
and the machine will switch off.  
10  
 
Wash cycles and functions  
Table of wash cycles  
GB  
Detergents  
Max.  
Max.  
Description of the wash cycle  
temp. speed  
(°C)  
(rpm)  
CLEAN Plus  
Anti Stain  
40°  
1600  
1600  
5
9
-
-
-
180’  
Cottons (Standard Cotton 60°) (1st press of the button) (1): heavily soiled whites  
and delicate colours.  
60°  
44 1,56 76 185’  
44 1,09 92 180’  
(Max. 90°)  
Cottons (Standard Cotton 40°) (2nd press of the button) (2): lightly soiled whites  
and delicate colours.  
40°  
1600  
9
9
Cottons (Standard Cotton 20°) (3rd press of the button): lightly soiled whites  
and delicate colours.  
Synthetics (Synthetics Resistant) (1st press of the button): heavily soiled resi-  
stant colours.  
Synthetics (Synthetics Resistant) (1st press of the button) (3): lightly soiled  
resistant colours.  
Synthetics (Synthetics Delicate) (2nd press of the button): lightly soiled delicate  
colours.  
20°  
60°  
40°  
40°  
1600  
800  
800  
800  
-
-
-
175’  
4.5 46 1,03 60 115’  
4.5 46 0,56 60 100’  
4.5  
-
-
-
75’  
SPECIALS  
Fast Wash 60' (1st press of the button): to refresh normal soiled garments quic-  
60°  
30°  
1600  
800  
3.5 44 0,84 44 60’  
3.5 71 0,20 38 30’  
kly (not suitable for wool, silk and clothes which require washing by hand).  
Fast Wash 30' (2nd press of the button): to refresh lightly soiled garments quic-  
kly (not suitable for wool, silk and clothes which require washing by hand).  
M My Cycle (Memory): allows for any wash cycle to be stored.  
Steam Refresh  
-
-
-
-
1.5  
-
-
-
20’  
EXTRAS  
Bed&Bath: washes bathroom laundry and bedlinen.  
60°  
40°  
1600  
800  
9
2
-
-
-
-
-
-
140’  
90’  
Wool (Woolmark Platinum) (1st press of the button): for wool, cashmere, etc.  
Delicates (2nd press of the button)  
30°  
0
1
-
-
-
80’  
Spin (1st press of the button)  
-
-
-
1600  
1600  
0
-
-
-
-
-
9
9
9
-
-
-
-
-
-
-
-
-
16’  
36’  
2’  
Rinse (2nd press of the button)  
Pump out (3rd press of the button)  
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-  
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.  
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle  
with a temperature of 60°C (1st press of the button).  
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be  
washed at 60°C. The actual washing temperature may differ from the indicated value.  
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle  
with a temperature of 40°C (2nd press of the button).  
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be  
washed at 40°C. The actual washing temperature may differ from the indicated value.  
For all Test Institutes:  
2) Long wash cycle for cottons: set wash cycle  
3) Long wash cycle for synthetics: set wash cycle  
with a temperature of 40°C (2nd press of the button).  
60°C (1st press of the button); with a temperature of 40°C (press TEMPERATURE button).  
Wash functions  
Time Saver  
Eco Wash  
If you select this option, the wash cycle duration will be redu-  
ced by up to 50%, depending on the selected cycle, thereby  
guaranteeing simultaneous water and energy saving. Use this  
cycle for lightly soiled garments.  
The Eco Wash function saves energy by not heating the  
water used to wash your laundry – an advantage both to  
the environment and to your energy bill. Instead, intensified  
wash action and water optimisation ensure great wash  
results in the same average time of a standard cycle.  
For the best washing results we recommend the usage of  
a liquid detergent.  
! It cannot be used with the , “Fast Wash 60’”,  
,
,
.
Steam Hygiene  
This option enhances washing performance by generating  
steam during the wash cycle that eliminates any bacteria  
from fibres while treating them at the same time. Place the  
! It cannot be used with the  
,
,
,
,
,
.
laundry in the drum, choose a compatible programme and  
select the function “Steam Hygiene”.  
! The steam generated during washing machine operation  
may cause the porthole door to become hazy.  
! It cannot be used in conjunction with  
(90°C),  
,
,
,
.
11  
 
Detergents and laundry  
Cotton Standard 20°  
: this programme is ideal for  
heavily soiled cotton loads. The effective performance  
levels achieved at cold temperatures, which are  
comparable to washing at 40°, are guaranteed by a  
mechanical action which operates at varying speed, with  
repeated and frequent peaks.  
Detergent dispenser drawer  
GB  
Good washing results also depend on the correct dose of  
detergent: adding too much detergent will not necessarily  
result in a more efficient wash, and may in fact cause a  
build up on the inside of your appliance and contribute to  
environmental pollution.  
! Use powder detergent for white cotton garments, for  
pre-washing, and for washing at temperatures over 60°C.  
! Follow the instructions given on the detergent packaging.  
Steam Refresh: this programme refreshes garments by  
removing bad odours and relaxing the fibres (1.5 kg, rou-  
ghly 3 items). Insert dry items only (that are not dirty) and  
select programme “ “. The garments will be damp once  
the cycle is completed, so we recommend hanging them  
to dry. The “ “ programme makes ironing easier.  
! Not recommended for wool or silk garments.  
! Do not add softeners or detergents.  
! Do not use hand washing detergents because these  
create too much foam.  
Open the detergent di-  
A
B
spenser drawer and pour  
in the detergent or washing  
additive, as follows.  
! The indicator light for the “Steam Hygiene” option will  
switch on when this cycle is selected.  
Bed linen and towels: use programme  
to wash bed  
*
1
linen and towels in one single cycle: it optimises softener  
performance and helps you save time and energy. We  
recommend the use of powder detergent.  
2
Wool: the wool wash cycle on this Hotpoint machine has  
been tested and approved by The Woolmark Company  
for washing wool garments labelled as hand washable  
provided that the garments are washed according to the  
instructions on the garment label and those issued by the  
manufacturer of this washing machine. Hotpoint is the  
first washing machine brand to be approved by The  
Woolmark Company for Apparel Care- Platinum for its  
washing performance and consumption of energy and  
water. (M1127)  
! Do not pour detergent into the middle compartment (*).  
Detergent should only be poured into the compartment 1.  
compartment 1: Detergent for the wash cycle  
(powder or liquid)  
If liquid detergent is used, it is recommended that the  
removable plastic partition A (supplied) be used for proper  
dosage.  
If powder detergent is used, place the partition into slot B.  
compartment 2: Additives (fabric softeners, etc.)  
The fabric softener should not overflow the grid.  
In UK, Eire, Hong Kong and India the Woolmark trade mark  
is a Certification trade mark.  
Delicates: use programme (2nd press of the button) to wash  
very delicate garments with decorative features, such as  
diamantes and sequins.  
Preparing the laundry  
• Divide the laundry according to:  
- the type of fabric/the symbol on the label  
- the colours: separate coloured garments from whites.  
• Empty all garment pockets and check the buttons.  
• Do not exceed the values listed in the Table of wash cycles”,  
which refer to the weight of the laundry when dry.  
To wash silk garments and curtains select the cycle  
(2nd press of the button) and set the “Delicate” level from  
option “Cleaning Action”.  
We recommend turning the garments inside out before  
washing and placing small items into the special bag  
for washing delicates. Use liquid detergent on delicate  
garments for best results.  
How much does your laundry weigh?  
1 sheet 400-500 g  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1200 g  
1 towel 150-250 g  
Load balancing system  
Before every spin cycle, to avoid excessive vibrations and  
to distribute the load in a uniform manner, the drum rotates  
continuously at a speed which is slightly greater than the  
washing rotation speed. If, after several attempts, the load  
is not balanced correctly, the machine spins at a reduced  
spin speed. If the load is excessively unbalanced, the  
washing machine performs the distribution process instead  
of spinning. To encourage improved load distribution and  
balance, we recommend small and large garments are  
mixed in the load.  
Special wash cycles  
Anti Stain : this programme is suitable to heavily-soiled  
garments with resistant colours. It ensures a washing  
class that is higher than the standard class (A class). When  
running the programme, do not mix garments of different  
colours. We recommend the use of powder detergent.  
Pre-treatment with special additives is recommended if  
there are obstinate stains.  
12  
 
Troubleshooting  
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure  
that the problem cannot be solved easily using the following list.  
GB  
Problem:  
Possible causes / Solutions:  
The machine does not switch on.  
• The appliance is not plugged into the socket fully, or not enough to make contact.  
• There is no power to the socket, or the fuse has blown in the mains plug.  
The wash cycle does not start.  
• The door is not closed properly.  
• The ON/OFF button has not been pressed.  
• The START/PAUSE button has not been pressed.  
• The water tap has not been turned on to allow water to flow into the machine.  
• A delayed start has been set (see “Running a wash cycle”).  
The machine does not fill with wa-  
• The water inlet hose is kinked.  
ter or “NO WATER CHECK SUPPLY • The water inlet hose is not connected to the water supply.  
appears on the display.  
• The water pressure is too low.  
• The water tap has not been turned on to allow water to flow into the machine.  
• There is no water supply to the house.  
• The inlet valve filter is blocked.  
• The START/PAUSE button has not been pressed.  
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65  
water and continually drains away  
or Water left in the drum  
or Stuck on wash.  
and 100 cm from the floor (see “Installation”).  
• The drain hose is connected incorrectly to the sink trap allowing water to run  
into the machine, the drain hose must be positioned higher than the bottom of  
the sink to prevent water flowing down the drain hose.  
• The end of the drain hose has been pushed too far down the standpipe, the  
‘U’ bracket should be fitted 100 mm from the end of the drain hose.  
The machine does not drain or spin • The Pump filter is blocked.  
or F05 error code in the display.  
• The drain hose is kinked (see “Installation”).  
• New Installation - The blanking cap or spigot has not been removed if con-  
nected under a sink.  
• The drain hose or sink trap is blocked.  
• The wash cycle does not include draining, some wash cycles require the drain  
phase to be started manually.  
• The ‘Spin Speed’ is in the “OFF” position.  
The machine does not heat or poor • The ‘Temperature’ is in the “OFF” position.  
wash results.  
The programme takes too long  
or The Display changes the estima-  
ted ‘Time to End’ during the pro-  
gramme.  
• Programme times will vary due to water pressure, the incoming water tempera-  
ture and if the wash load goes out of balance. This will increase the programme  
times accordingly (see ‘ The machine wont spin properly’ below).  
The machine vibrates a lot during  
the spin cycle.  
• The feet have not been adjusted, enabling the machine to rock.  
• New Installation - Either the Transit Bolts including the plastic spacers, or the  
Polystyrene Packaging have not been removed when installing the machine.  
• The machine is trapped between cabinets and/or walls.  
• The load is in a slight out of balance condition and machine is spinning, but at  
a lower speed.  
13  
 
The machine is noisy.  
• There will always be some motor, pump and drum noise during spin.  
GB  
The machine wont spin properly.  
• Out of Balance detected when attempting to go into a spin cycle - If this  
happens the machine will continue to try to repeat the distribution of the load  
required before the machine will go into higher spin speeds - This will increase  
the programme time accordingly. This is a safety feature to prevent damage.  
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,  
etc). - Try the programme again using a different load.  
The machine leaks from the di-  
spenser.  
• The dispenser drawer is blocked with detergent and requires cleaning.  
• The water pressure is too high and requires turning down - turn down the tap  
on the water supply pipe slightly and try again.  
• The machine is tilting forwards - It must be level when in its final position.  
The machine leaks (other than  
dispenser).  
• The fill hose is loose, check both the cabinet and tap ends.  
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill  
hose is missing the rubber washer.  
• The drain hose is not fixed in properly.  
The indicator lights on the console  
are flashing rapidly.  
• Switch off the machine and unplug it, wait for approximately 1 minute and then  
switch it back on again If the problem persists contact the Technical Assistance  
Service.  
The machine smells.  
• The machine requires a service wash. Run a “Auto Clean” wash cycle with  
detergent and no laundry.  
The machine door cannot be  
opened.  
• The door will not open until the door lock indicator light goes out shortly after  
the program has finished.  
Door Seal damaged at the bottom.  
• The door seal has drainage holes at the bottom - This is normal.  
• The water level is correct if it can be seen at the bottom of the door.  
The water level is too low when  
the machine is washing.  
There is too much foam.  
• The detergent is not suitable for machine washing (it should display the text  
‘for washing machines’ or ‘hand and machine wash’ or the like).  
Too much detergent was used - less detergent is required in soft water.  
After completing the programme,  
or before starting a programme,  
the machine has turned itself off  
(no lights).  
To comply with new energy saving regulations the machine is fitted with an  
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate  
the machine, it can then either be switched off or a new programme selected.  
General.  
Your washing machine contains sensors that monitor progress during the wash  
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-  
gress).  
Normally, if your machine successfully completes the cycle, there is unlikely to  
be anything wrong!  
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed  
above.  
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.  
Do not wash items which do not have a wash label, or wash items that are not intended as machine  
washable.  
14  
 
Assistance  
Guarantee  
12 Months Parts and Labour Guarantee  
GB  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs  
for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of  
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost  
to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result  
of improper installation.  
Replacement of any consumable item or accessory . These include but are not limited to: plugs,  
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL  
OR NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will  
be a charge for our engineers time. To activate the extra parts warranty on your appliance, simply call our  
registration line on 08448 24 24 24 (ROI 01 230 0800).  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair  
bills for the life of your policy. To find the ideal plan for you please call our advice line on  
08448 226 226 (Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service  
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where  
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will replace your  
machine or, if you prefer, give you your money back.  
15  
 
195105699.00  
06/2012  
-
Xerox Fabriano  
After Sales Service  
No one is better placed to care for your Hotpoint appliance during the course of its working  
life than us - the manufacturer.  
GB  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000  
fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee  
you must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17  
Recycling & Disposal Information  
As part of Hotpoints continued commitment to helping the environment, Hotpoint reserves the right to use  
quality, recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove  
the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to  
ensure that the appliance can no longer be plugged into a mains socket, and the door  
16  
 

Graco Ventilation Hood 77X540 User Manual
Grizzly Saw G1023SLW User Manual
Guardian Technologies Portable Generator 02010 2 04164 3 User Manual
Haier Clothes Dryer HWD1600BW User Manual
Hamilton Beach Coffeemaker BrewStation User Manual
Hamilton Beach Oven 31160 User Manual
Hasbro Robotics 87524 User Manual
HP Hewlett Packard Photo Printer 8400 Series User Manual
HP Hewlett Packard Switch 2512 User Manual
Impex Home Gym IGS 07 User Manual